The Seasonal House
22 Nov 2026

Checking your insulation

Insulation is one of the few house jobs where doing nothing for years is normal. It sits in the ceiling and under the floor, out of sight, and nobody notices it until the house is cold and damp. A check once every few years, or whenever you are buying or renting, tells you whether it is still doing its job.

Autumn suits the task. The ceiling space has cooled from the summer peak, the weather is usually dry, and any fix can be done before winter. The notes below follow the standard that applies to rentals, which is a useful yardstick for any house.

What the rental standard asks for

Tenancy Services publishes the healthy homes insulation standard. It sets minimum R-values, and R-value measures resistance to heat flow, so a higher number is better. The figures depend on climate zone: ceiling R2.9 in Zones 1 and 2 and R3.3 in Zone 3, with underfloor R1.3 in all zones. Zone 1 is the top of the North Island, Zone 2 the coastal North Island, and Zone 3 the centre of the North Island and the whole South Island. The page does not name Auckland's zone, so use the zone map or the insulation tool on the Tenancy Services site to confirm yours (Tenancy Services, insulation standard). The zone figures apply to properties that received building consent before 3 November 2022.

An owner-occupier is not bound by this standard, but it is an official reference point if you want to know what a minimum looks like.

Look in the ceiling space

If you can reach the ceiling space safely, look at three things.

Thickness. Tenancy Services says existing ceiling insulation installed before 1 July 2016 must be at least 120 mm thick under the standard. Thinner insulation can pass if the landlord can show it met the minimum R-value when installed and has not degraded by more than 30 per cent since. You can measure thickness yourself with a tape or ruler.

Labels. The R-value of new insulation is printed on the packaging, and for existing insulation the packaging may be stapled to a beam, so look along the joists for a label.

Condition. The standard says existing insulation must be in reasonable condition, with no mould, dampness, damage or gaps. Look for areas where it has been disturbed by tradespeople, where it has slumped or compressed, where it does not reach the edges, and around downlights, hatches and cable runs.

Take care in the roof space. Step only on the ceiling joists, take a torch, wear a mask and gloves, and let someone know you are up there. If the idea does not appeal, hire a professional installer to assess it. The standard says insulation must be installed to NZS 4246:2016, so ask an installer to work to it.

Look under the floor

Underfloor insulation is harder to see. If there is a subfloor space you can safely get into, check whether insulation is fixed to the underside of the floor, whether it has sagged or come away, and whether it is damp. Tenancy Services says that if a rental has an enclosed subfloor, a ground moisture barrier must be installed where reasonably practicable, and Consumer NZ also suggests installing a vapour barrier under the house to stop moisture coming up from underneath. A bare soil floor with no barrier is a quiet source of damp in the whole house.

The signs you can see from inside

Even without opening the hatch, the house gives hints:

Mould in particular is a flag. Tenancy Services says a dry, well-aired home is easier to heat and healthier, and Healthify lists insulating the house and fixing building and plumbing leaks as the first steps for preventing damp. If you find damp insulation, find the source before replacing it: a roof leak, a failed flashing, or a bathroom fan that vents into the roof space will wet new insulation too.

What to do with the result

If the insulation is thin, compressed or gappy, there are three practical routes.

  1. Top it up or fill gaps. Often a cheaper fix than replacement, depending on what is already there.
  2. Replace damaged sections. Remove wet or mouldy material and fix the cause first.
  3. Get a professional assessment. Useful when you cannot tell the R-value or the product is old.

Healthify notes that Warmer Kiwi Homes offers grants covering 50 to 90 per cent of insulation costs for eligible households, so check eligibility before paying for the work yourself (Healthify, damp and mouldy homes). Entitlements change, so use the programme's own site to confirm the current rules.

Other jobs to bundle with the check

Since you are already in the ceiling space or the subfloor, look at the things that share it: whether bathroom and rangehood ducts end outdoors, whether there is any sign of roof leaks above the insulation, and whether cables and downlights are clear of the material. Keep a dated note of what you found, the thickness and any labels, because it saves repeating the climb in future.

Insulation and the rest of the year

Most owners add insulation to slow heat loss in winter. Consumer NZ also notes that heat is let out of a house through windows and draughts, so curtains and sealed gaps do more of the work when the insulation is already good. A check each autumn costs an hour and a torch battery, and it tells you whether winter's heating bills are going to be about the house or about the insulation.

Sources

Also this year:
The Seasonal House: a year-round home maintenance guide for Auckland and northern New Zealand. General guidance only; check current rules and product labels.