Cleaning mould safely
Mould shows up in Auckland houses most often in autumn and winter, according to Tenancy Services, when windows stay shut and cold surfaces meet warm, wet air. The usual response is to grab a spray and scrub. A better one is slower: protect yourself, clean without spreading spores, and then deal with the moisture that fed it.
What you are dealing with
Consumer NZ describes mould as a type of fungus that grows in damp areas, usually appearing as coloured growth (green, grey, brown, black, white or red) or stains on walls, ceilings and other surfaces. It produces thousands of tiny spores that float in the air and can be inhaled. Some species are toxic, such as Stachybotrys chartarum, commonly known as "black mould", although not all black mould is that species. Other species can trigger allergic reactions or asthma symptoms. People with weak immune systems, asthma or a respiratory problem are at particular risk.
Healthify notes that touching or breathing in mould or spores can cause irritation and allergic reactions, including a runny nose, red eyes, skin rashes and respiratory problems. Babies and children, older adults, people with eczema, allergies or asthma, and people with weakened immune systems can have more severe symptoms. If someone in the household has symptoms you are concerned about, talk to a doctor or nurse.
Check the surface first
How easy the job is depends on what the mould is growing on. Consumer NZ separates three cases:
- Non-porous surfaces, such as plastic and glazed tiles, are relatively easy to clean.
- Super-porous materials, such as clothing, furniture, wicker baskets and cardboard, are harder. The mould may not come out completely and the item may need to be thrown away.
- Grout and silicone are difficult, because once mould gets in, it is almost impossible to remove from where it has grown roots, known as mycelium. You may have to replace the silicone or re-grout.
Large patches found behind walls are another matter. Consumer NZ says they should be tested to see whether they are black mould, and that if you suspect it, a professional mould removal service is the sensible call (Consumer NZ, top tips for avoiding mould in your home).
Protect yourself first
Before touching it:
- Ventilate the room by opening windows.
- Wear disposable gloves, eye protection and a well-fitted face mask. Consumer NZ says a P2, N95 or respirator mask is best.
- Do not dry-brush mould, because that can release spores into the air.
- Keep children and pets out of the room.
Healthify's list is the same: gloves, eye protection and a safety mask. Read the label on any cleaning product, because some give off fumes.
Cleaning a small patch
For small patches on non-porous surfaces, Consumer NZ lists soapy water, diluted bleach (1 part bleach to 4 parts water) or diluted vinegar (9 parts vinegar to 1 part water). The government-linked advice varies a little: Tenancy Services and Healthify describe a bleach mix of 1 part bleach to 3 parts water, and white vinegar and water in equal parts, which on painted surfaces should be left for a few days before wiping off with soap and water. The evidence about the best method is inconsistent, according to a 2019 report from PHF Science cited by Consumer NZ, so the choice comes down to the surface, the label and what you are comfortable using.
The method matters more than the mix:
- Never mix bleach and vinegar. Consumer NZ warns that this creates toxic chlorine gas.
- Patch-test first on a small area, especially on paint or fabric.
- Wipe gently with a cloth rather than scrubbing hard. Use a clean sponge or cloth and rinse it often to reduce the chance of spreading mould.
- Dry the area well afterwards.
- Throw away the cloths you used on mould.
Commercial mould killers usually contain bleach as the active ingredient, listed as sodium hypochlorite, though the concentration is often 5 per cent or less, so do not assume a branded product works faster than a diluted household one.
When to stop and call a professional
Consumer NZ recommends a specialist for large patches behind walls or any suspected black mould. A building surveyor may also need to look if mould keeps coming back. Tenancy Services says that if a rental stays damp and mouldy even though the tenant is doing everything right, they should talk to the landlord, because a hidden source of damp left long enough can cause expensive damage.
Mould that is still visible, or smells musty after cleaning, can point to a hidden moisture problem behind the lining or under the floor. Treat that as a building issue rather than a cleaning issue.
Fix the cause
Cleaning mould without drying out its cause is a temporary measure. Healthify lists building leaks, faulty plumbing, flooding and condensation from bathrooms, laundries and kitchens as causes of damp, along with little or no airflow in cupboards. The fixes are the ordinary ones:
- dry washing outside, use lids on pots and run extractor fans, checking they vent outside rather than into the roof space;
- wipe condensation from windows and walls each morning;
- pull furniture slightly away from external walls, and keep wardrobe doors a little open;
- open windows for 10 to 15 minutes a day;
- use a dehumidifier or a heat pump's dry mode if moisture persists;
- fix leaking gutters, downpipes and plumbing.
Consumer NZ says that mould is most likely where warm, moist air from showers and cooking meets cold surfaces. Heating the house, using curtains and sealing draughts all make condensation harder to form (Healthify, damp and mouldy homes).
Rentals and responsibilities
Tenancy Services says rental homes must be free from mould and dampness before being rented out, and tenants need to keep the house well aired and remove mould straight away during a tenancy. Gutters, downpipes and drainage are the landlord's side of it. If you rent, note any mould at the initial inspection and report persistent damp in writing. Rules change, so check the current guidance at Tenancy Services.
After the clean
Once the patch is gone and the surface is dry, look at it again in a week. If nothing has grown back, you probably dealt with the moisture. If it has, the source is still there. Repainting over mould without addressing the cause is a waste of paint.