Servicing a heat pump
A heat pump is one of the lower-maintenance appliances in a house, and it is also one of the most neglected. Most of what it needs can be done in ten minutes with a vacuum cleaner, and the rest is paying attention to the outdoor unit. The best time to do it is autumn, before the first cold week, when you can fix a problem without being cold while you wait.
This guide sets out what is worth doing yourself, how often, and what is a job for a technician.
How often to clean
Consumer NZ gives a simple rule of thumb that depends on how much you use the unit. If you use the heat pump sparingly in winter, once a year is probably enough. If you run it heavily through both summer and winter, aim for at least four times a year (Consumer NZ). Most Auckland households sit somewhere in between, and a good approach is to clean before winter, check again in midwinter and clean again in spring.
Dusty homes, houses with pets and units in kitchens or living areas with cooking will need cleaning more often than a unit in a spare bedroom. Look at the filter: if you can see a mat of dust, it is time.
The indoor unit
The filters are the main job. Consumer NZ's steps:
- Turn the unit off at the remote, and if you are uncertain, off at the wall switch or switchboard as well. Check your owner's manual.
- Open the front panel and slide out the filters.
- Vacuum them with a brush attachment.
- Vacuum the vanes and fins inside the unit, gently.
- Wipe the outside of the unit with a damp cloth.
- Put the filters back and close the panel.
The same source says filters often get clogged if they have not been cleaned for a few months, and that cleaning clogged filters can noticeably improve heat output. It estimates a DIY clean takes under ten minutes. If the unit comes with a washable filter, your manual will say how to wash it, so follow the manufacturer's instructions rather than guessing.
A note on mould
Mould on the outer panels is common, because condensation forms there, especially when the unit is cooling, and it wipes off like any other surface mould. Mould on the fins or filters, however, probably extends inside the unit. Consumer NZ advises getting a professional to clean it, because otherwise you risk blowing mould spores through your home. Do not spray cleaning products into the unit yourself. If you have anyone in the house with asthma or other respiratory conditions, call a technician rather than disturbing it.
The outdoor unit
The outdoor unit sits on a wall bracket or a pad and gets ignored. Consumer NZ suggests:
- Keep vegetation trimmed back from the unit, and don't let objects lean against it.
- Check for signs of insect nests or colonies, such as ants or cockroaches. Small problems can be treated by you; large ones need a pest professional.
- Look for corrosion and deal with it, or have it dealt with, to extend the unit's life.
Some water on the ground beside the outdoor unit is normal, because the unit drains condensation. Water inside the house is a problem. Leaves, spider webs and cobwebs across the grille cut airflow, so brush off loose debris gently.
Auckland's humid coastal conditions are hard on outdoor equipment, so look at the unit's base, fixings and brackets as well as the casing. If the unit has settled or the bracket looks rusty, have it looked at.
Before you trust it for the winter
After cleaning, turn the heat pump on and listen. Consumer NZ recommends listening for abnormal sounds and checking that the unit produces plenty of heat, both indoors and at the outdoor unit.
Also check:
- The remote's batteries.
- Any timer settings, which may need adjusting for winter.
- Whether the room heats evenly. If one side of the room is cold, the louvres may need to be redirected.
When to call a technician
Consumer NZ says a professional service every few years is optional, for peace of mind and diagnostic checks, and that otherwise you should call a technician when a fault develops. The warning signs are strange noises, leaking inside the house, or poor performance even after cleaning the filters. Add to those:
- A burning smell or smoke, in which case turn it off at the switchboard and call an electrician or technician.
- An error code that does not clear after a restart.
- Ice building on the outdoor unit that does not go away.
- A unit that runs but does not heat or cool at all.
The sealed refrigerant system is a technician's job, not an owner's.
Running it alongside good ventilation
A heat pump is no substitute for ventilation. Consumer NZ's guidance on reducing moisture advises opening windows daily, even in winter, to let damp air out, and keeping heating low and steady rather than running high bursts, which reduces condensation (Consumer NZ). A heat pump suits that approach well. Set a modest steady temperature, close the doors of the room being heated, and open a window briefly once a day. A clean filter also helps the unit keep up, since clogged filters cut heat output.
A yearly routine
- Autumn: Clean the filters, inspect the outdoor unit and test run it.
- Midwinter: Check the filter again if the unit has been running every day.
- Spring: Clean the filters again and trim back vegetation around the outdoor unit.
- Summer: If you use it for cooling, clean the filters again before the heat arrives.