Spring and early summer: checking the timber
Timber houses talk to you if you know when to listen. In Auckland, the warmer months are when wood-boring beetles leave the timber, which means the evidence is at its freshest from late spring into summer. A short, methodical inspection at that time of year tells you more than the same inspection in July, when old holes and new ones look alike.
This is a guide to what to look for and where. It will not replace a professional inspection before you buy a house, but it will help you notice a problem early and ask better questions.
What is happening in the wood
Consumer NZ lists up to seven borer species in New Zealand. The common house borer is the usual culprit, and the native two-toothed longhorn is also common but less likely to be found in buildings. The adult beetles fly for about a month, between November and March, to mate. In the common borer, eggs hatch within four to five weeks and the larvae can stay in the timber for up to four years (Consumer NZ).
That life cycle explains the timing. Damage is done by the larvae, years before you can see anything. What you can see is the adult's exit hole, and fresh holes and fresh dust appear when the adults leave. Understanding the borer flight season helps you pick the right weeks to look.
What to look for
Consumer NZ describes the signs of common house borer as small round flight holes of about 2 to 4 millimetres and piles of fine sawdust on timber, doors or furniture. The two-toothed longhorn leaves larger holes, up to 7 millimetres, which are more oval.
Look for:
- Clusters of round holes in bare, unpainted timber.
- Fine, pale dust under holes or in the corners of a ledge or shelf, particularly if it appears again after you wipe it away.
- Timber that sounds hollow or crumbles when pressed with a screwdriver.
- Furniture or joinery with holes on one face.
Old holes stay visible indefinitely. Clean dust on a clean surface a week later is a stronger sign than a hole alone.
Where borer likes to be
Consumer NZ notes that borer attacks untreated and damp timber, and that it is often found on the south side of buildings and in floor timbers. Soft sapwood and untreated native timber in older homes are common targets, and sawn timber is more prone to attack than smooth surfaces. Keeping the area under the floor well ventilated helps prevent it.
So the inspection route is:
- Under the house. Check the underside of floorboards, joists and bearers with a torch. Check that the underfloor vents are not blocked by plants or stored items.
- The roof space. Look at rafters, roof battens and any untreated framing.
- The garage and sheds. Untreated offcuts and shelving are often the first place borer shows.
- Joinery and skirting. Run a torch along the surface at a low angle. Light raking across wood shows holes clearly.
- Weatherboards on the south and shaded sides. Look for holes and dust at the bottom edges.
Moisture is part of the picture. The Consumer NZ guidance on reducing dampness advises clearing vegetation from underfloor vents and says moisture rising from the ground can be significant under a house with bare soil. Fixing drainage and guttering problems first, then considering a sealed moisture control sheet over the ground, is the order it recommends (Consumer NZ). Dry, ventilated timber is a less appealing home for any wood-boring insect.
Weatherboards and hidden damage
An important point from the Consumer NZ borer guidance is that borer often attacks weatherboards from the inside, so the damage may be more extensive than the surface suggests. Where boards are affected, the advice is to replace them and treat the framing while the wall is open. If a board is soft or the paint is lifting over a cluster of holes, do not assume the damage stops at the surface.
Treatment: what works and what does not
The same source says the only long-term option is a residual surface treatment with an insecticide or preservative, applied to bare timber. Fogging, misting and bombs only kill adults in flight and do not stop the larvae, so they are not a solution. Fumigation can suit furniture but is not usually suitable for houses. Severely weakened timber should be strengthened or replaced, and large infestations should be treated by a professional.
That has a practical consequence for the DIY owner. If you find a few holes in an offcut in the garage, you can deal with it. If you find holes in a floor joist, bearer or weatherboard, get an assessment first. When you are buying, selling or unsure what you have found, an independent inspector such as Lignum Timber Inspections can tell you which species is present, how active it is and whether the timber is still sound. Ask for a written report that records where the damage is and how it was assessed.
A November routine
- Pick a dry day and take a torch, a screwdriver and a notebook.
- Start under the house, then the roof space, then outside.
- Photograph holes next to a ruler, so you can compare them next year.
- Wipe a small patch of dust from a ledge near suspect timber and check it again in a week.
- Fix any dampness you find: blocked vents, leaking gutters or downpipes, plumbing leaks.
Doing this each year takes an hour. It means any change shows up while the fix is still small.